Features of the RF-BLOK shielded design: Reduced interference from one piece EMI (Electromagnetic Interference)/RFI (Radio Frequency Interference) shield Increased insulation resistance up to 25% No soldering requirements as interconnect design needs no 360 degree soldering
- eliminating the possibility of human error and/or cracking of the solder that causes grounding intermittence & the use of the most hazardous waste material
- soldering flux Tight fit of internal wires as there is no inner mould No requirement of ferrite cores as signal loss & degradation are greatly reduced giving enhanced signal sharpness. Without the ferrite cores the cable is less stressed & more flexible Smaller overall

Dimensions which allows more room behind the host or peripheral Increased connector & mating strength
- the 4 point reinforcement tabs on the RF-BLOK, attached to the connector, strengthens the pair as one Important! Please note that cable lengths over 7.5m are above the recommended length laid down by the DDWG organisation who developed the

Specification. This factor also depends on the hardware combination of graphics card & monitor as to how far this distance can be exceeded.






...

Features of the RF-BLOK shielded design: Reduced interference from one piece EMI (Electromagnetic Interference)/RFI (Radio Frequency Interference) shield Increased insulation resistance up to 25% No soldering requirements as interconnect design needs no 360 degree soldering
- eliminating the possibility of human error and/or cracking of the solder that causes grounding intermittence & the use of the most hazardous waste material
- soldering flux Tight fit of internal wires as there is no inner mould No requirement of ferrite cores as signal loss & degradation are greatly reduced giving enhanced signal sharpness. Without the ferrite cores the cable is less stressed & more flexible Smaller overall

Dimensions which allows more room behind the host or peripheral Increased connector & mating strength
- the 4 point reinforcement tabs on the RF-BLOK, attached to the connector, strengthens the pair as one Important! Please note that cable lengths over 7.5m are above the recommended length laid down by the DDWG organisation who developed the

Specification. This factor also depends on the hardware combination of graphics card & monitor as to how far this distance can be exceeded.






...

4 Way RJ-11 Male to 4 Way BT Telephone Male Straight-through wiring 10 year warranty ...

2 x LC Fibre Optic Male to 2 x LC Fibre Optic Male Compatible with all standard fibre optic equipment & connectors Full duplex 50/125m type fibre Zip twin, LS0H, Multimode cable Ceramic connectors ensure low signal loss & high reliability Total immunity to electrical & electromagnetic interference (EMI) Insertion Loss: ...

The LINDY OM3 cables allows new VCSEL based hardware & old legacy LED hardware to co-exist on one system. Installing an OM3 optical fibre solution gives a simple migration path from 1 Gbs to 10 Gbs & the security of knowing the system will give many years of solid, secure service to your network. ...

2 x LC Fibre Optic Male to 2 x SC Fibre Optic Male Compatible with all standard fibre optic equipment & connectors Full duplex 50/125m type fibre Zip twin, LS0H, Multimode cable Ceramic connectors ensure low signal loss & high reliability Total immunity to electrical & electromagnetic interference (EMI) Insertion Loss: ...

The LINDY OM3 cables allows new VCSEL based hardware & old legacy LED hardware to co-exist on one system. Installing an OM3 optical fibre solution gives a simple migration path from 1 Gbs to 10 Gbs & the security of knowing the system will give many years of solid, secure service to your network. ...

2 x LC Fibre Optic Male to 2 x SC Fibre Optic Male Compatible with all standard fibre optic equipment & connectors Full duplex 62.5/125m type fibre Zip twin, LS0H, Multimode cable Ceramic connectors ensure low signal loss & high reliability Total immunity to electrical & electromagnetic interference (EMI) Insertion Loss: ...

2 x LC Fibre Optic Male to 2 x ST Fibre Optic Male Compatible with all standard fibre optic equipment & connectors Full duplex 50/125m type fibre Zip twin, LS0H, Multimode cable Ceramic connectors ensure low signal loss & high reliability Total immunity to electrical & electromagnetic interference (EMI) Insertion Loss: ...

2 x LC Fibre Optic Male to 2 x ST Fibre Optic Male Compatible with all standard fibre optic equipment & connectors Full duplex 62.5/125m type fibre Zip twin, LS0H, Multimode cable Ceramic connectors ensure low signal loss & high reliability Total immunity to electrical & electromagnetic interference (EMI) Insertion Loss: ...